GMRS seems to be the communication method of choice for most off-road enthusiasts these days. If you’re going the GMRS route, then there isn’t a more powerful FCC-approved addition to your arsenal than the Midland USA 40 watt GMRS MXT400 MicroMobile two-way radio.
In October of 2019, Midland USA became our latest gear sponsor. They sent us two MXT400 Micro Mobile radios for our adventures. (Thank you, Midland!)
But once we received them, we had to install them. Enter my good friend Paul Jones. As soon as we arrived back in Austin for the holidays, I went over to Paul’s house and we knocked out the install together.
I provide links below to this item we actually use. These are affiliate links and Amazon will give us a little bit if you end up buying through us. It’s a nice way to say thanks for this article, and it doesn’t cost you anything extra to buy through our links.
Why the Midland MXT400 MicroMobile GMRS Radio?
Even though we’re starting our seventh year of full-time travel in 2020, we’ve never towed the Jeep behind our RV. Not once. We actually use the Jeep as it was designed–as a scout vehicle. So when we’re driving, we need a reliable form of communication between the two vehicles.
Up until now, we’ve been communicating using the 5 watt Midland GXT 1000VP4 hand held GMRS radios when we’re out on the open road. While these radios are great for what we’ve used them for, there have been many times during our extensive travels when we wished we had a much longer range.
Imagine Basecamp our RV, sitting by itself off-grid in the middle of a no cell coverage area. Caspian and Brittany are hanging out and I’m miles away on the trails, or I’ve run into town for something–farther away than the handhelds can communicate. Without cell service, there’s no way to contact the family back at Basecamp.
With the 40 watts of power in the MXT400s, this is an issue of the past.
Unobstructed, the MXT400s can communicate a whopping 65 miles away. With partial obstructions, they can still communicate 15-20 miles. With heavy obstructions, you’re looking at 5-10 miles.
We’ve done several tests we’ll have to write about in another article. But suffice it to say, these radios have some serious power. For safety, security, and peace of mind, we’re really thankful to have added these radios to our overlanding arsenal.
The Jeep Install
The install in our Jeep was fairly straight-forward. Though there were some acrobatics involved. If you don’t own a Wrangler, then you won’t understand. But if you do, then you know exactly what I’m talking about. But that’s #JeepLife, right?
The steps that follow are for a Jeep Wrangler JKU, but you can adjust as needed for your vehicle.
Step 1: Decide on a location in the vehicle where the radio is going to live.
We decided to mount our radio on top of our Vector Off Road JKE Dock. Here I have quick access to all of the radio controls; it doesn’t obstruct line of sight; and the mic is readily accessible. (Jeep-specific)
Step 2: Remove passenger side dash panel. (Jeep-specific)
Step 3: Remove plastic casings (covers) from the fuses on the power and ground wires to allow them to fit through the firewall.
Really nice touch from Midland to put these fuses in removable casings. If they hadn’t, this part of the install would have been a nightmare.
Step 4: Run power wires through the firewall hole and replace casings.
Step 5: Add ring terminals to power wires, to attach them to the battery.
We added ring terminals because we are powering our radio using the Genesis Dual Battery setup. Most installs will not require Step 5. But for those with the Genesis Dual Battery system, make sure you have some ring terminals.
Step 6: Connect power wire to the battery.
Step 7: Run power wires through the windshield channel to the radio. (Jeep-specific)
Though acrobatics are often required for these types of installs in a Jeep, we’re really thankful Jeep included so many ways to get wires through and around the dash, and windshield.
Step 8: Decide on location for antenna.
Unfortunately, there aren’t too many options with a Jeep Wrangler, since the roof has little to no metal. So we went with a longer antenna on a magnetic mount, and placed it on the hood of the Jeep on the passenger side.
Step 9: Run the antenna cable from the mount point through the engine compartment to the driver side, along the windshield wiper housing. (Jeep-specific)
Step 10: Remove the horn to allow access to the firewall on the driver side. (Jeep-specific)
We had already relocated the horn because of the ARB Dual Air Compressor. If you’re installing one of these radios in a Wrangler, you’ll probably skip this step.
Step 11: Run the antenna cable through the firewall on the driver side.
Step 12: Remove driver-side dash panel. (Jeep-specific)
Step 13: Run the antenna cable through the windshield rubber gasket channel. (Jeep-specific)
Step 14: Connect antenna cable to the radio.
Step 15: Button up all dash panels and clean up all wiring.
That’s it. Radio installed.
We powered ours on and began tests. As I said, that will have to be another article down the road, after we’ve had a chance to put these radios through their paces across differing terrain.
Closing Thoughts on Our Midland MXT400 MicroMobile Install
As you can see, our installation was pretty straight-forward. Even though some acrobatics were necessary, the radio install itself was a breeze. I’d say about an hour to an hour and a half, tops.
But nothing ever goes this smoothly, right? Nope.
During the install, Paul and I had been messing around with some fuses in the fusebox, and pulled the fuse for the ARB Dual Air Compressor. We forgot about it and moved on to the rest of the install. As always when finishing up anything with power, we tested everything that has power in the vehicle to make sure we didn’t do anything screwy. Sure enough, everything worked EXCEPT for the air compressor.
Being the Jeep savants we are, we were sure we must’ve pulled an air compressor power line loose when yanking the antenna wire through the driver side firewall. So we spent the next five hours taking all of the wiring for pretty much everything in the Jeep apart, trying to figure out where the problem was.
When we finally remembered about playing around in the fusebox, we were a little embarrassed we missed something that simple. But we had some good laughs and camaraderie. Don’t judge us.
Bottom line, the radio is installed and it’s amazing. Everything else is operational as it should be, and all is right with the world.
If you’ve been on the fence about a permanently-mounted GMRS solution for your vehicle, then I’d encourage you to give the Midland USA MXT400 MicroMobile a look. It’s a solid addition to any overlanding arsenal.
If this article was helpful to you it would be awesome if you’d consider becoming a Jeepsies supporter. If everyone just gave $1, we could do these articles full time and that is our dream. There are some fun options in the drop-down below. Your support allows us more free time to create high quality content regularly. You can say a quick thanks here: Even if you aren’t ready to support Jeepsies financially, please do comment on the articles, ask questions and let us know that you are here and hopefully we can meet up sometime on the trail! And if you haven’t followed the Jeepsies Facebook page you can do so here. Also, we’re on Twitter and Instagram if you use those platforms. Please give us a follow, we’d love to hear from you. Until next time, keep it dirty and wheels side down. ~ Eric, Brittany, and #LittleNomad